Green Bay 920-499-2117 | Peoria 309-697-1760 | Woodstock 815-477-9680 | Contact Information
Handi Pier
YOUR KIT
INCLUDES: G E T TIN G S T A R T E D HANDI PIER® CONCRETE HEAD (1) GALVANIZED STEEL RODS (4) ROD DRIVER PLUGS (4) ROD CAPS (4) INSTALLATION INSTURCTIONS WARRANTY INFORMATION
YOU WILL ALSO NEED FOR INSTALL:
AUTOMATIC DRIVER HAMMER AND SDS MAX DRIVER BIT FOR 1 1/8″ PIPE (BIT AVAILABLE AT MENARDS) SAFETY GLASSES , GLOVES & EAR PROTECTION SHOVEL, LEVEL & TAPE MEASURE SLEDGEHAMMER OR MAUL SILICONE CAULK AND CAULKING GUN TWO OR MORE PEOPLE TO ASSIST IN INSTALL
Handi Pier
STEP 1:
Identify the location of each HANDI PIER® needed for the project. Dig a hole the approximate size and shape of its head. This hole should be slightly larger than the head allowing for some loose fill under it. Position the head in the hole and ensure it is level. Pack soil around it to help maintain its position during the rest of the install.
STEP 2:
Using a mallet, assemble the rod driver points into one end of each rod (4 per HANDI PIER®).
STEP 3:
Insert the rods in the 4 holes in the head with the driver point down and insert to a depth of a foot or so with the sledge or maul.
STEP 4:
Using the automatic hammer, carefully drive in each rod alternately and in increments. Finish driving the rods to the appropriate depth leaving approximately 3/4″ of the rod exposed.
CAUTION: If the rod meets an obstacle that cannot be driven through, you may need to attempt to remove the obstacle. If this is not feasible, the head can be rotated. See the full Installation Manual at handipier.com for troubleshooting techniques.
STEP 5:
After all 4 rods are inserted, caulk around the rod at the head sleeve. This will help alleviate any concerns of moisture penetrating the head assembly
STEP 6:
Finish filling in dirt around its head. Place the 4 caps on the rods and continue the project using a 4″ or 6″ post bracket. Caps can be removed for inspection
Handi Pier
Important Information
Before installing HANDI PIER®, confirm that there are no underground utilities, wires, cables, etc in the area where it will be located. Keep in mind the width of the installed HANDI PIER® 50″ rod is approximately a 3′ radius or a total of 6′ diameter and the 63″ rod is approximately a 3.5′ radius or a total of 7′ diameter around your pier.
Calculate the spacing of the project so that each HANDI PIER® is supporting up to its designed maximum load capacity. Check your local building codes for requirements. It should not be installed in any un-compacted fill or loose soil.
HANDI PIER® is designed to be installed in normal soil conditions. The 2 common types are sand/gravel and silts/clays. DO NOT install it with soil conditions less than 2000 psf sands/gravel and 1500 psf silt/clay.
HANDI PIER® is not designed to be used on slopes greater than 27° or on any location that may have shifting or sliding soils.
HANDI PIER® is designed to be used on structures supported by posts and beams, no rotational or dynamic loads should be supported on it. Ideal for decks, elevated patios, and platforms. Always check your local building codes before installing its foundation systems.
It is ICC-ES certified with ERS 4404.
Complete the HANDI PIER® Warranty at www.HandiPier.com. For Warranty registration and claims, refer to the Batch # on the bottom right-side of this guide found inside the parts bag attached to each head at time of purchase.
For use with One & Two Dwelling Construction Only. See ICC-ES Evaluation Report No. 4404 at www.icc-es.oeg. HP-R 50 & 63 must be installed with HANDI PIER® Rods, Caps and Drivers Only. See Complete Installation Instructions, Load Chart & Warranty Information at www.HandiPier.com.
Handi Pier
This is Modal Title
